Training Internal & External Corrosion Control & Monitoring For Pipeline & Surface Facility

INTRODUCTION Training Internal & External Corrosion Control & Monitoring For Pipeline & Surface Facility:

Corrosion control and monitoring course focuses on corrosion – from either internal or external source – and its potential problem, and the protection methods to stop or control them. Review on corrosion and technique by which it can be identified, monitored and controlled will be given in detail. Active participation is encouraged through case studies and examples especially on the use of painting and coatings, transformer-rectifier of impressed current, magnesium, zinc and alum sacrificial anodes for external protection, and the injection of corrosion inhibitors and biocides for internal corrosion control.



PRE-REQUISITE
:

NONE. No previous training in corrosion control is required. However, to gain the most from this course, a basic understanding of physics, chemistry and basic unit operations will be helpful.



TRAINING MATERIAL OUTLINE :

  1. Review of oil & gas surface production facility and operations.
  2. Review of metallic materials used in surface production facility and pipelines and the corrosion problem usually happen.
  3. Case studies and examples of oil & gas material failure caused by corrosion from internal and external source.
  4. Uniform, galvanic and localized corrosion failures.
  5. Internal corrosion of pipeline, vessel and processing equipment caused by sour component, H2S, CO2, organic acid, brine, and the SRB (sulfate reducing bacteria).
  6. External corrosion of underground, underwater and under-seawater pipeline and structure caused by impurities in soil and water environment.
  7. External corrosion of topside structure caused by marine atmosphere.
  8. Basic electrochemistry of corrosion process, Ohm’s law and the corrosion rate.
  9. Corrosion control and prevention with painting & coatings and the cathodic protection.
  10. Measurement of corrosion potential and corrosion current.
  11. Protection with sacrificial anode and impressed current.
  12. Understanding NACE Standard RP-01-69 to stop external corrosion attack.
  13. Requirement, design and criteria of cathodic protection.
  14. Sacrificial anode specification, installation and construction.
  15. Testing, monitoring, and inspection of cathodic protection.
  16. Inspection and maintenance of transformer-rectifier and sacrificial anode.
  17. Field test, measurement techniques and instrument.
  18. Data recording and evaluation of cathodic protection system.
  19. Case studies of corrosion control and prevention with cathodic protection.
  20. Internal corrosion problem in the pipeline and surface facility.
  21. Oil/gas/water fluid properties and the corrosion tendency.
  22. Deterioration by H2S, CO2, and acidic corrosive components.
  23. Pipeline leakage and rupture by microbial induced corrosion.
  24. Corrosion caused by SRB and the pitting mechanism.
  25. Corrosion caused by oxygen penetration.
  26. Examples and case studies of equipment corrosion damage and pipeline leakage.
  27. Understanding NACE Standard RP-0775 for internal corrosion control and monitoring.
  28. Practical internal corrosion monitoring methods.
  29. Access fittings, corrosion coupon and corrosion probes.
  30. Practical internal corrosion control and prevention methods.
  31. Internal corrosion control with inhibitors and the selection of suitable corrosion inhibiting chemicals.
  32. Dosage and injection methods of corrosion inhibitors.
  33. SRB control with biocides and the selection of suitable and low risk biocide formula.
  34. Dosage and injection methods of biocides.
  35. Oxygen control by de-aeration and chemical injection, and the selection of suitable oxygen scavenger chemicals.
  36. Dosage and injection methods of oxygen scavenger.
  37. Safety in the use of chemicals for internal corrosion prevention.
  38. Review of gas dehydration process and operations.
  39. Internal corrosion problem in glycol contactor (dehydration) unit.
  40. Method and materials use to control the corrosiveness of rich glycol solution.
  41. Review of amine sweetening process and operations.
  42. Internal corrosion problem in amine sweetening unit.
  43. Method and materials use to control the corrosiveness of rich amine solution.
  44. Examples and case studies of internal corrosion control

Kami dapat menyelenggarakan Public Training ataupun inhouse Training Internal & External Corrosion Control & Monitoring For Pipeline & Surface Facility di seluruh wilayah indonesia. Untuk mendapatkan info training Internal & External Corrosion Control & Monitoring For Pipeline & Surface Facility serta mendaftarkan diri anda mengikuti training Internal & External Corrosion Control & Monitoring For Pipeline & Surface Facility yang akan kami selenggarakan, anda dapat mengirim surel di email kami trainingsemangatindo@gmail.com atau anda dapat pula mengisi formulir pra registrasi yang tersedia dibawah ini. 

Form Request Training
  1. Isi Data Berikut ( Tidak Mengikat )
  2. (required)
  3. (valid email required)
  4. (required)
  5. (required)
  6. (required)
  7. (required)
  8. (required)
  9. (required)